Hoses, Lines & Fittings

A hose clamp or hose clip is a device used to attach and seal a hose onto a fitting such as a barb or nib. A hose clamp is not the same as a pipe clamp which is a clamp made partly out of a pipe, not a clamp for clamping pipe.

more...

Home
ATV Parts
Apparel & Merchandise
Automotive Tools
Aviation Parts
Boats Parts
Car & Truck Parts
Car Audio, Video
Manuals & Literature
Motorcycle Parts
Other
Other Vehicle Parts
Personal Watercraft Parts
Racing Parts
Accessories
Auto Racing Parts
Body & Exterior
Chassis, Suspension & Brakes
Driveline & Transmission
Other
Rear End
Transmission
Electrical
Chips, Programmers
Ignition
Other
Wiring Kits
Engine & Components
Exhaust
Fuel Systems
Fuel Injection & Pumps
Fuel Pressure Regulators
Hoses, Lines & Fittings
Other
Induction
Carburetors
Cold Air Intake
Forced Induction
Intake Manifolds
Nitrous Oxide
Other
Interior
Gauges
Other
Seats
Other
Wheels & Tires
Fasteners, Fluids & Gaskets
Kart Racing Parts
Other
Safety Equipment
Services & Installation
Snowmobile Parts
Vintage Car & Truck Parts
Wholesale Lots

Types

Many types are available, including :

Screw/band clamps

Screw clamps consist of a band (usually stainless steel in the USA) into which a screw thread pattern has been cut or pressed. One end of the band contains a captive screw. The clamp is put around the hose or tube to be connected, with the loose end being fed into a narrow space between the band and the captive screw. When the screw is turned, it acts as a worm drive pulling the threads of the band, causing the band to tighten around the hose. Screw clamps are normally used for hoses 1/2 in diameter and up, with other clamps used for smaller hoses.

Pairs of screw clamps on a short rubber unit form a "no-hub band," often used for attaching sections of domestic wastewater piping, or used for other pipes as a flexible coupler (to fix alignment difficulties or to prevent pipe breakage due to relative movement of sections) or an emergency repair.

They can also be used in a similar way, as a simple means for the transmission of small amounts of power. A short length of hose is clipped between two shafts where vibration or variations in alignment may be taken up by the flexibility of the hose. This technique is well adapted to use for mock-ups in a development laboratory.

This type of clamp was invented in 1921 by ex Royal Navy Commander, Lumley Robinson, who founded L. Robinson & Co (Gillingham) Ltd which exists to this day as a family business still based in Gillingham, Kent. The company still owns the registered trade mark 'Jubilee Clip', which is registered in countries all over the world.

A similar type of clamp to the screw band, also with a solid screw and an interesting history, described here: Marman clamp.

Spring clamps

Spring clamps are typically made from a strip of spring steel, cut so that one side has a narrow protrusion centered on the end, and the other side a pair of narrow protrusions on either side. The ends of these protrusions are then bent outwards, and the strip rolled to form a ring, with the protruding tabs intermeshing. To use the clamp, the exposed tabs are pressed towards each other (typically using pliers), increasing the diameter of the ring, and the clamp is slid onto the hose, past the portion that will go onto the barb. The hose is then fit onto the barb, the clamp expanded again, slid onto the portion of the hose over the barb, then released, compressing the hose onto the barb. Clamps of this design are rarely used for high pressures or large hoses, as they would require unwieldy amounts of steel to generate enough clamping force, and be impossible to work with using just hand tools. They are commonly used on automotive cooling system hoses several inches in diameter, for example on most water-cooled Volkswagen automobiles.

Read more at Wikipedia.org